AR-700S1G4A 700 Watt CW, 0.8 - 4.2 GHz
RATED OUTPUT POWER: 700 W minimum
INPUT FOR RATED OUTPUT: 1.0 mW Max
POWER OUTPUT @ 3dB COMPRESSION: Nominal 700 watts; Minimum, 625 watts
POWER OUTPUT @ 1dB COMPRESSION: Nominal 600 watts; Minimum, 525 watts
FLATNESS: ±2.0 dB typical, ±2.5 dB maximum
FREQUENCY RESPONSE: 0.8-4.2GHz instantaneously
GAIN (at maximum setting): 59 dB minimum
GAIN ADJUSTMENT (Continuous Range) : 15 dB minimum
INPUT IMPEDANCE: 50 ohms, VSWR 2.0:1 maximum
OUTPUT IMPEDANCE: 50 ohm nominal
MISMATCH TOLERANCE:
100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. See Application Note #27.
MODULATION CAPABILITY: Will faithfully reproduce AM, FM, or pulse modulation appearing on the input signal
HARMONIC DISTORTION: -20 dBc maximum at 700 W
THIRD ORDER INTERCEPT POINT: 67 dBm typical
Remote Interfaces:
- IEEE-488, 24 pin female
- RS-232, 9 pin Subminiature D (female)
- Fiber Optic, ST Conn Tx and Rx RS-232
- USB 2.0, Type B
- Ethernet, RJ-45
The Model 700S1G4A is a portable, self-contained, air-cooled, broadband, completely solid-state amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. Push-pull circuitry is utilized in all high power stages in the interest of lowering distortion and improving stability. The Model 700S1G4A, when used with a sweep generator, will provide a minimum of 700 watts of RF power.
The Model 700S1G4A is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the amplifier. The DCP uses a color LCD touch screen and a single rotary knob to offer status reporting and control capability. The display provides Forward Power and Reflected Power values plus amplifier status. Special features include a gain control and RF output level protection.
All amplifier control functions and status indications are available remotely in GPIB/IEEE-488 format, RS232 hardwire and fiber optic, USB and Ethernet. The buss interface connector is located on the back panel and positive control of local or remote operation is assured by a keylock on the front panel of the amplifier.
The low level of spurious signals and linearity of the Model 700S1G4A make it ideal for use as a driver amplifier in testing wireless and communication components and subsystems. It can be used as a test instrument covering multiple frequency bands and is suitable for a variety of communication technologies such as CDMA, W-CDMA, TDMA, GSM etc. It is also suitable for EMC Test applications where undistorted modulation envelopes are desired.
The Model 700S1G4A is a portable, self-contained, air-cooled, broadband, completely solid-state amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. Push-pull circuitry is utilized in all high power stages in the interest of lowering distortion and improving stability. The Model 700S1G4A, when used with a sweep generator, will provide a minimum of 700 watts of RF power.
The Model 700S1G4A is equipped with a Digital Control Panel (DCP) which provides both local and remote control of the amplifier. The DCP uses a color LCD touch screen and a single rotary knob to offer status reporting and control capability. The display provides Forward Power and Reflected Power values plus amplifier status. Special features include a gain control and RF output level protection.
All amplifier control functions and status indications are available remotely in GPIB/IEEE-488 format, RS232 hardwire and fiber optic, USB and Ethernet. The buss interface connector is located on the back panel and positive control of local or remote operation is assured by a keylock on the front panel of the amplifier.
The low level of spurious signals and linearity of the Model 700S1G4A make it ideal for use as a driver amplifier in testing wireless and communication components and subsystems. It can be used as a test instrument covering multiple frequency bands and is suitable for a variety of communication technologies such as CDMA, W-CDMA, TDMA, GSM etc. It is also suitable for EMC Test applications where undistorted modulation envelopes are desired.